Antennacraft HDMS9100 Manuel d'utilisateur télécharger pdf (Page 6)

There may be cases that the receiver is triggered by another

transmitter in your neighborhood, or a nearby RV with the

same antenna.

If you nd the receiver is receiving and reacting to some

commands which have not been sent from your remote

control, you can change the Transmitter/Receiver ID code

pair by following the below procedures:

1. Unplug the power cord from the receiver.

2. Hold down the ‘UP’ and ‘DOWN’ keys together and power

up the receiver until the LCD shows “Id” . The receiver is

now in the ID programming mode.

With the remote control near to the receiver, hold down its ‘9’

and ‘0’ keys until the ‘Id’ on the receiver LCD disappears.

Changing the Transmitter/Receiver ID Code

4. Press ‘1’, ‘2’, ‘3’ to select code 1, 2 or 3 respectively within

2½ seconds after the receiver LCD is emptied.

5. The receiver should now show “x “, where “x” represents

the Code number that you’ve set.

6. Press the ‘STORE’ key on the remote control within 2½

seconds after pressing ‘1’, ‘2’ or ‘3’ for code selection.

7. The receiver should now show “Id x”.

8. The new ID code pair is stored. Unplug the receiver and

then plug it in again for the new ID to be in effect.

Note: You can use one of 3 identifying code numbers. The

default ID code used is 1. Review the notes below.

After the ‘9’ and ‘0’ buttons on the remote control, are released,

then choose and press either the ‘1’, ‘2’ or ‘3’ keys within 2½

seconds. If any other button is pushed, it will exit the ID pro-

gramming mode. This is to avoid any accidental button pushed

on the remote control. If this happens, start at Step 1 again.

After code number ‘1’, ‘2’ or ‘3’ is selected, users should

push the ‘STORE’ button on the remote control within

2.5 seconds. If no other button than ‘STORE’, ‘1’, ‘2’

or ‘3’ is pushed, it will exit the ID programming mode.

This is to avoid any accidental button pushed on the

remote control. If this happens, start at Step 1 again.

If the receiver is unplugged before it has been stored

(Step 8 above) the new ID code will not be saved.

Observation

Possible Problem Actions

No Display on LCD

No power connected.

The receiver is in ID programming mode and no

appropriate command is received from the remote.

Connect the power.

Power reset the receiver and

repeat the ID pair up.

LCD freezes with ‘CA’ upon

power up

The motor control wires (red, blue) are not connected.

The antenna rotation is obstructed.

Connect the wires*.

Clear the obstacles.

LCD displays ‘Er’

The position feedback wire (black) is not connected.

The coaxial cable is not connected.

The 3 control wires (red, black, blue) are reversed.

Connect the wire*.

Connect the cable*.

Correct the wire connection*.

LCD displays ‘Er’ and ‘CA’

during idle

Intermittent connection of the position feedback wire

(black).

Fix the wire connection*.

LCD freezes during ID

programming

The receiver is in ID programming mode and no

appropriate command is received from the remote.

Power reset the receiver and

repeat the ID pair up.

Receiver has no response to

the remote control

The remote control is out of battery.

The ID code is mismatched.

Change the battery.

Pair up the ID code.

After changing the antenna

position, it returns to the

original number

The motor control wires (red, blue) are loosened.

The antenna rotation is obstructed.

Fix the wires*.

Clear the obstacles.

* The receiver should be power reset after xing the wire connection.

Trouble Shooting

The below provides information for problem diagnosis in case the antenna control system is not working properly. The receiver

may sometimes display messages when its operation is interrupted.

7. Use the left or right arrows on the remote to select the

optimized antenna direction. Finally, press “STORE” again

to save the setting.

8. To recall a stored channel and direction, enter the chan-

nel number directly by using the number button on the

remote control. The antenna will then turn to the direction

that corresponds to the channel number you entered on

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Antennacraft HDMS9100 Manuel d'utilisateur Page 6

Commentaires sur ces manuels